RationalDMIS 2020 薄板件向量创建测量时的接近/回退设置

    在测量薄板件小孔时，需要比较小的接近/回退距离，但有时向量创建采样平面有时不是很平，小的接近/回退距离会导致碰撞。在这种情况下，需要设置软件分别控制两个接近/回退距离。

软件默认的为无独立控制：

此处单独控制向量创建采样点的接近/回退距离，特定类型的工件由于偏差较大，需要采样点接近/回退距离单独控制，不同于整体测量参数；

设置成单独控制后就可以输入向量创建点的接近/回退数值了。测量小孔的接近/回退距离还是在原来的位置设置，见下图红色框：

设置完成后，将元素拖放到测点管理窗口后，点击测量即可实现：向量创建测量点的接近/
回退距离为10，而元素的测量点的接近/回退距离为2.

MODE/PROG,MAN

SNSET/APPRCH, 2.0000

SNSET/RETRCT, 2.0000

SNSET/DEPTH, 3.0000

SNSET/SEARCH, 10.0000

SNSET/CLRSRF, 20.0000

F(CIR1)=FEAT/CIRCLE,INNER,CART,31.5000,31.5000,0.0000,0.0000,0.0000,1.0000, 20.0000

$$ Measurement points are created through nominal points

$$ Senset adjustment for independent VECBLD sampling control

  SNSET/APPRCH, 10.000000

  SNSET/RETRCT, 10.000000

RMEAS/CIRCLE, F(CIR1), 5, VECBLD, 3.0000, 3

  RPTMEAS/CART, 44.5000, 31.5000, 0.0000, 0.0000, 0.0000, 1.0000

  RPTMEAS/CART, 25.0000, 42.7583, 0.0000, 0.0000, 0.0000, 1.0000

  RPTMEAS/CART, 25.0000, 20.2417, 0.0000, 0.0000, 0.0000, 1.0000

  SNSET/APPRCH, 2.000000

  SNSET/RETRCT, 2.000000

  GOTO/CART, 36.5844, 26.6887, 6.0000

  PTMEAS/CART, 38.7634, 24.6267, -3.0000, -0.7263,  0.6873, -0.0000

  GOTO/CART,   37.8223, 28.4953, -3.0000

  GOTO/CART,   38.4414, 30.5961, -3.0000

  GOTO/CART,   38.3810, 32.7854, -3.0000

  PTMEAS/CART, 40.2814, 36.2840, -3.0000, -0.8781, -0.4784, -0.0000

  GOTO/CART,   36.3113, 36.5844, -3.0000

  GOTO/CART,   34.5047, 37.8223, -3.0000

  GOTO/CART,   32.4039, 38.4414, -3.0000

  PTMEAS/CART, 29.6638, 41.3300, -3.0000,  0.1836, -0.9830, -0.0000

  GOTO/CART,   28.1512, 37.6470, -3.0000

  GOTO/CART,   26.4156, 36.3113, -3.0000

  GOTO/CART,   25.1777, 34.5047, -3.0000

  PTMEAS/CART, 21.5837, 32.7913, -3.0000,  0.9916, -0.1291, -0.0000

  GOTO/CART,   24.6190, 30.2146, -3.0000

  GOTO/CART,   25.3530, 28.1512, -3.0000

  GOTO/CART,   26.6887, 26.4156, -3.0000

  PTMEAS/CART, 27.2076, 22.4681, -3.0000,  0.4292,  0.9032, -0.0000

ENDMES